All Rights Reserved. No part of this manual, including the products and software described in it, may bereprod. Refer to thefollowing table for the LED sta. ASUS APE2 barebone serverThis chapter lists the hardware setupprocedures that you have to perform wheninstalling or removing system components. Chapter 2: Hardware setup You can simply. Match and insert the hooks of thecover to the elong. The motherboard. Locate the pin ZIF socketson the motherboard. Flip up thesocket lever and push.
Use a Phillips screwdriver totighten the four heatsink screwsin a diagonal sequence. Connect the fan cable to the Repeat steps 1 to 3 to install theother heatsink if you haveinstalled a second CPU, thenconnect the fan cable to t. Chapter 2: Hardware setupDo not use too much force when removing the front panel assembly. Unhook the hinge-like tabs from the holes on the rig. When released, pull up the drive bay lock bar.
Underneath the lock barare two pegs that match the holes on the dr. Make sure that the drive and bayholes align as shown. When inplace, the drive protrudes aboutan inch from the front p. Carefully insert drive tray. Connect the IDE and powercables to their correspondingconnectors on the back of thedrive.
Follow steps 2 to 6 if yo. Press the dummy cover into theslot opening until the hook tabclicks in place. When installed, the dummy coverap. This design feature a.
When the card is in place, secureit with the plastic card lock thatyou removed earlier. Card lock tab. When the card is inside thechassis, push down the end ofthe card until it is level with thePCI slot.
Remove the plastic card lock that secures the expansi. You do not need to disconnect these c. Thisside includes the power connectors, SA. This side includes the powerconnectors,. Operation is subjectto the following two condi. Chapter 2: Hardware setupTo re-install the chassis fan Insert the new fan to the chassisfan cage. Pull the fan out from the fan case,then se. Loosen the thumb screw thatsecures the HDD fan cage to thechassis. Hold the.
Press the fan case hooks outwardsuntil the fan detaches from thecase. Slightly press the center of thefan vent to f. Re-connect the 3-pin fan cable tothe fan connector on the backplane.
Push the outer edge of the fancage sideway. Remove the HDD fan cage. Position the backplane into itsslot with the component sidefacing the rear pa. Carefully pull out the drive fromthe chassis until you see thecables connected to the drive.
Position the floppy drive verticallywith the eject button on the leftside close t. Refer to sec. Lay the system chassis on its side. Use a Phillips screwdriver toremove the screws. Loosen the thumbscrew thatsecures the power supply metalplate. Chapter 2: Hardware setupTo install a W single power supply module Firmly hold the power supplymodule and insert it into thepower supply c.
Loosen four screws on the metalbrackets that secure the powersup. Use a power supply modulehandle to push the power supplyuntil it fits in place. Secure the power supply to thechass. Chapter 3Installation options. You are able to switch between the different cameras to access the settings information for each of them. Nickname In this section, you will be able to enter a nickname for your camera. Simply type the name into the box and then click on apply.
Now, that camera will go by that particular nickname when it shows up on the left side of the screen. Page 14 3. You will see a red dot next to the Setting icon identifying that there is a new upgrade available. Page 15 3. After the mobile detection is opened, the alarm information can be sent to the mobile phone when the camera detects the moving events and the objects are moved.
Page 16 3. Page 17 3. The Cloud Box is an ideal DIY Do It Yourself security solution for homes and small businesses that require the recording of many hours of continuous video. Page 18 3. The Network Tab enables you to choose the network interface that you want to use - Ethernet or Wi-Fi.
Page Others 3. You can make the Others volume higher or lower with these sliders. Sliding to the right makes the volume go higher, and sliding to the left makes it lower. Flip is used when the camera is mounted upside down for example, when it is attached to a ceiling.
If devices have been added, the current image for each active device is shown in the dashboard. Page Main Interface 4. Keep in mind that when you are changing the settings, which we will be discussing in this chapter, the camera must first be live and active. Page Pan, Tilt 4. These controls are only available as you move the mouse to hover over the display edges top,bottom, left and right in the middle. Not all cameras provide the full range of rotation, panning, tilting, etc.
Use the adjustment tube to secure the cables comfortably. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Here are some general tips to follow for safe use of this product: 1.
A 27D Rev. They are also ideally suited for use with CD players, MP3 players, notebook computers and any other listening device that has a 3. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need.
0コメント